NHTSA Office of Defects Investigation
Preliminary Evaluation PE19-008: Seat belt buckle bracket failure
- Closed
NHTSA's Office of Defects Investigation opened Preliminary Evaluation PE19-008 on July 29, 2019 and closed it on December 12, 2019. NHTSA's investigations file lists the 2011–2018 Jeep Wrangler for it and links recall 19V-680 to it.
Updated daily from NHTSA's investigations file
Key facts
- NHTSA number
- PE19-008 (also written PE19008)
- Investigation type
- Preliminary Evaluation The first stage of most defect investigations: NHTSA's Office of Defects Investigation gathers basic information about a possible safety defect, including from the manufacturer.
- Status
- Closed December 12, 2019
- Opened
- Closed
- Vehicle or equipment manufacturer
- Chrysler (FCA US, LLC)
- Component
- Seat Belts — Front — Buckle Assembly
- Recall linked by NHTSA
- 19V-680: Seatbelt Buckle May Separate From Seat Frame, reported
- Vehicles and equipment
- 2011–2018 Jeep Wrangler
NHTSA's summary
As NHTSA's Office of Defects Investigation wrote it for Preliminary Evaluation PE19-008.
On July 17, 2019, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 19-008 after receiving three Vehicle Owner Questionnaire (VOQ) reports alleging the driver's side seat belt buckle separated from the seat frame, rendering the seat belt non-functional. The VOQs involved model year (MY) 2015 and 2016 Jeep Wrangler (JK platform) that were configured for right-hand drive (RHD) use. On August 8, 2019, ODI issued an information request (IR) letter to FCA.The scope of the IR included all JK Wrangler produced for sale in the U.S. (both left- and right-hand drive), and amongst other things, requested any reports or allegations of driver's seat belt bracket failures on these vehicles. In its review of FCA's response, ODI determined that approximately 1.7 million JK Wrangler were produced from MY 2007 to 2018, about 16,000 of which were configured for RHD. ODI notes that the RHD Wrangler are typically used for rural postal delivery which often experience a more severe duty cycle. Also RHD JK was was not produced in MY 2007.
As explained in the IR response, FCA identified three distinct populations of JK Wrangler concerning the driver's seat belt bucket bracket; specifically the MY 2007-2018 LHD (~1.7M units), the MY 2008-2010 RHD (4,563 units), and the MY 2011-2018 RHD (11,463 units) populations.
FCA provided details on the designs used in each of these populations, identifying specific differences deemed pertinent to the strength and durability of each unique bracket design. FCA further reviewed its analysis of the complaint and warranty data identified under the IR, and noting that it had not identified any allegations of bracket failures on the LHD population, and only one allegation on the MY 2008-2010 RHD vehicles. By comparison, FCA identified 24 allegations of bracket failure for the MY 2011-2018 RHD JK, including two reports duplicative of the VOQs. Neither the FCA nor the VOQ reports allege an injury or fatality due to bracket failure. Based on this analysis, FCA decided to conduct a safety recall for the MY 2011-2018 RHD JK population. On September 30, 2019, FCA submitted a Defect Information Report initiating NHTSA Safety Recall 19V-680 (FCA No. VA6). Under the recall action, FCA will replace the driver's seat belt bracket on MY 2011-2018 RHD Jeep JK Wrangler. The repair will be conducted free of charge.
In view of FCA's recall action, and its explanations of the scope of that action, ODI is closing PE19-008. ODI will continue to monitor the non-recalled RHD, and the LHD JK Wrangler for evidence of seat belt bracket failure and will take further action if warranted.
The three VOQ reports cited above can be reviewed at NHTSA.gov under the following reference numbers:11190251, 11218472, 11231639.
Vehicles and equipment listed for this investigation
NHTSA's investigations file lists these vehicles and equipment for Preliminary Evaluation PE19-008. A listed model year means only that an investigation names it; it says nothing about any particular vehicle. Model years with a try.vin recall page link to that page's NHTSA investigations section.
What an NHTSA investigation is
NHTSA's Office of Defects Investigation (ODI) looks into possible safety defects in vehicles and equipment, often after owner complaints. An investigation usually starts as a Preliminary Evaluation, or as a Recall Query when it concerns whether an existing recall covers the right vehicles or fixes the problem, and ODI can upgrade it to a more detailed Engineering Analysis. A Defect Petition asks NHTSA to open an investigation, and Audit and Equipment Queries are administrative investigations into whether companies complied with federal vehicle safety requirements, such as reporting, recall and certification rules.
An open investigation is not a finding that a safety defect exists, and NHTSA can close one without a recall.
To see whether a specific vehicle has an open recall, enter its VIN at nhtsa.gov/recalls.
Jeep VIN check: decode a VIN to see its year, make and model.
Sources
NHTSA's investigation record for PE19-008
Investigation details come from NHTSA's investigations file, which try.vin imports once a day. The investigation types are described from the U.S. Department of Transportation Inspector General's May 2023 report on NHTSA's Office of Defects Investigation, NHTSA's petition rules (49 CFR Parts 552 and 557) and NHTSA's Office of Defects Investigation procedures. How try.vin reads NHTSA investigations.