2013 Ford Focus Recalls, Ratings & Complaints

Incident: September 5, 2026 · Filed: September 25, 2026

Transmission error stating clutch A engaged. Yes, the vehicle is available for inspection. My safety and the safety of others were put at risk because the vehicle would not move after being stopped at the stop light or stop sign or stop during traffic.

Incident: July 28, 2026 · Filed: September 23, 2026

The vehicle suffered a major mechanical and electrical failure on July 28, 2026, and was immediately towed to an authorized dealership. After a multi-day delay awaiting a senior technician's analysis, the dealership issued a single service ticket grouping two distinct issues: a failed Canister Purge Valve (active Safety Recall 26S40) and localized wiring damage. The dealership fraudulently drafted the ticket to imply that external rodent damage caused the recall component failure. However, forensic photographic proof uploaded to the manufacturer database on August 13, 2026, reveals a classic consequential engineering failure: the wiring insulation is severely bubbled and thermally fused from extreme internal circuit resistance caused entirely by the defective recall component. An adjacent plastic snack wrapper remains completely pristine and untouched, disproving the rodent narrative. The vehicle has now been held in safety detention for 57 consecutive days. A corporate supervisor explicitly confirmed on a recorded line that the manufacturer has possessed these forensic photos since mid-August but left the safety file stagnant due to an internal database text-field error. Their software is failing to match the vehicle's engine string '2.0L I4 DI Ti-VCT' to the recall applicability screen 'GDI', creating a data-entry roadblock to deny a free safety remedy. I am requesting an immediate federal audit of the manufacturer's database alignment for Recall 26S40 and a manual technical override directive to initiate repairs. Manufacturer Master Case: CHX-09386351-T9Y5H1.

Incident: August 28, 2026 · Filed: September 9, 2026

RE: FAULTY THROTTLE WIRING / LOCATION CAUSING CORROSION 2013 FORD FOCUS - RECALL NEEDED To Whom It May Concern: My 2013 Ford Focus SE Flex with VIN [XXX] lost power while traveling from [XXX] to [XXX] a couple times before completely dying. My code reader was getting fixed throttle codes 2112, 2111 and pending codes 122, 223. I switched out the throttle body AND accelerator pedal position sensor. This did NOT resolve the issue. I had the Focus towed to Downey Ford in [XXX] where they found a Technical Service Bulletin stating endless Focuses had this issue with corroded wiring, which appears to be caused by TSB 15-0036, which is regarding the wiring harness rubbing against a sharp part of the intake, which can cause shorts in the cables. This Ford Dealership repair cost me $845.80 + grief + an extended stay at my hospitable parents in [XXX]. This concern should be escalated to RECALL status as it leaves your loyal customers stranded on the roadside. My request is a full refund from Ford for $845.80 CAD. See Downey Ford Invoice # SO # XXX attached. Source: [XXX] [XXX]: Bear with me, this is going to be a bit long. TL;DR: Car will not accelerate, CEL/MTC states problem with "accelerator pedal position sensor". Wiring harness has been cut into by rubbing on intake. I want to splice it to fix it, but need advice due to length/resistance requirements. Two weeks ago, my wife was driving my 2013 Ford Focus SE Hatchback and right as she got off the freeway, it instantly lost power, a message appeared on the screen stating "Engine Fault - Repair Now", and it idled super rough. She restarted the engine and it was fine until she tried accelerating more than a tiny bit, at which point the same symptoms occurred again. She was able to limp the car home. Having misplaced my OBD2 scanner, I limped it over to the local auto parts store and they read the code as INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Incident: August 20, 2026 · Filed: September 2, 2026

I purchased a 2013 Ford Focus from Boucher Ford of Menomonee Falls, WI in February, 2026. A few months later, Ford issued a recall on this car that requires the Powertrain Control Module to be reprogrammed to avoid issues like a collapsed fuel tank or stalling while driving, potentially causing an accident. I had been informed by a mechanic that this car was sold to me with a custom tune on the PCM. This tune was not disclosed to me when I purchased the car and due to the PCM being modified, the recall cannot be performed without damage to the PCM rendering the car undriveable. I tried working with Jeff Samp (General Manager) at the dealership but he told me they were not required by law to check for tunes when a car is traded in and that he could have someone "look at the car" but if they damage the PCM performing the recall, they will not be held responsible. I opened a case with Ford Motor Company and was informed that they would escalate to some kind of dealership oversight department and that it might take a couple weeks to get a response. I never received a response so I called Ford to inquire and was told that they are not sure why I was told that, that no such department exists, and that all they can do is call the dealership on my behalf and "ask" them to deal with it. Facts: 1. They sold me a car with a modified Powertrain Control Module which can affect many things, even falsely disabling check engine lights. 2. A FEDERAL RECALL for my own safety cannot be performed on this vehicle IN THE CONDITION THEY SOLD IT TO ME, putting my safety, my passengers' safety, and the safety of other motorists at risk. 3. Boucher Ford will not remedy this issue or even contact the previous owner as I requested to find out what kind of tune is on this vehicle so that I can get it removed and this safety recall performed. I want the PCM replaced with a new unit, with the new software that complies with this recall.

Incident: September 2, 2026 · Filed: September 2, 2026

The contact owns a 2013 Ford Focus. The contact stated that the transmission failed, and the vehicle lost motive power, and the vehicle was stuck in the middle of traffic. The contact referenced several satisfaction programs for the issue; however, the VIN was not included in the repair. The vehicle was towed back to the residence due to it not being able to operate. The contact stated there was an unknown warning light on the instrument panel. The contact stated that the transmission had overheated. The manufacturer was notified of the failure. The vehicle was taken to an independent mechanic, and it was confirmed with transmission failure.

Incident: November 22, 2016 · Filed: August 31, 2026

Issue happened in November 2016. The glass sunroof exploded while driving NE on I-44 just SW of Springfield MO. The reason I am reporting this now, is that I saw a news article about this happening often. Until I saw the news article I thought it was a one of event. We did not witness anything hitting the car/sunroof. I don't expect anything from this report. I just wanted report that a Ford Focus experienced this type of event.

Incident: June 11, 2026 · Filed: August 21, 2026

See attached document for complaint.

Incident: April 2, 2026 · Filed: July 14, 2026

The evap canister purge valve has been a recurring problem for this vehicle. The canister was replaced in 2021, but continued having problems, as it pulled a vacuum on the fuel tank in upwards of 3/8 inch. (Documented by Murray Ford in 2023 and reassuredthere was no issue by them) the vehicle has displayed inaccurate fuel readings and caused our family to be disabled and then stranded in the night on highway 95. It put the safety of my family, and other motorists at risk The problem hasn't been duplicated because their "software fix" essentially ignored the problem altogether. There were no warnings. According to my vehicle it had at least 50 miles til empty. The fuel sending unit is displaying innacurqte fuel readings, and the fuel pump has displayed symptoms, characterized by surging, stalled when accelerating from a stop, and of course, completely shutting off, while on the highway. I've tried my best to trust and be patient with Ford and for them to do the right thing, but have been brushed off.

Incident: April 2, 2026 · Filed: July 14, 2026

I am reporting a severe vehicle safety hazard and engine stalling incident on my 2013 Ford Focus caused by an un-remedied factory emissions safety defect (related to Ford Recall 26S40 / 18S32). Due to an incomplete factory software monitoring patch, the canister purge valve stuck open and allowed continuous, unchecked engine vacuum to pull straight out of the plastic fuel tank. This heavy vacuum physically collapsed and deformed the bottom of the plastic fuel tank inward by approximately 0.25 to 0.375 inches. This structural collapse compressed the internal fuel pump assembly and mechanical float arm, falsifying the dashboard fuel gauge and distance-to-empty calculations. On April 2nd, while driving on Interstate 95 at midnight, the vehicle displayed an inaccurate fuel level, ran completely dry, and suffered a sudden engine stall in high-speed traffic without warning. My family and I were trapped in a highly hazardous situation and were forced to physically push the disabled vehicle 3 miles down the highway in total darkness. We ultimately had to enlist the emergency intervention of the Florida State Patrol Road Rangers to dispatch a unit and supply fuel so we could safely clear the interstate. The vehicle has since thrown a hard diagnostic trouble code P0443, confirming a complete electrical circuit malfunction of the EVAP system. Ford's failure to successfully deploy a functional software monitor has caused severe structural damage to my fuel system and created an imminent, life-threatening safety risk to my family on public highways. I am requesting a federal record of this incident to compel a full vehicle inspection and complete fuel system component replacement by the manufacturer."

Incident: May 20, 2026 · Filed: June 4, 2026

I had my purge valve replaced under 24N07 ford costumer satisfactory program and the faulty purge valve damaged my catalytic converter and caused my engine light to illuminate with P0420.