NHTSA vehicle safety data

2010 Mazda MAZDA6 Recalls, Ratings & Complaints

The 2010 Mazda MAZDA6 has 9 NHTSA recall campaigns and 225 owner complaints on file as of November 3, 2026. Recall repairs are usually free at an authorized Mazda dealer.

NHTSA recall and complaint data for the 2010 Mazda MAZDA6, plus NCAP crash-test ratings. Recall data is refreshed daily from NHTSA.

Pre-purchase inspection checklist → Reliability & 5-year cost forecast →

2010 Mazda MAZDA6 owner complaints

Owners have filed 225 complaints with NHTSA about the 2010 Mazda MAZDA6, describing incidents dated February 1, 2010 to June 23, 2026.

Most-cited components

Structure 60 complaints
Air Bags 54 complaints
Suspension 43 complaints
Unknown or Other 33 complaints
Steering 29 complaints
Exterior Lighting 21 complaints

Of the 225 complaints on file, 5 report a crash and 2 a fire; across all 225 complaints, owners report 2 injuries (owner-reported, not verified by NHTSA).

Newest complaints

ODI #11746080 · Filed June 23, 2026
I recently had my front subframe replaced as part of your recall, however, the rear subframe and all components attached are suffering from the exact same rust and potential component failure as the front. I was replacing my brakes today and noticed that the entire structure is on the verge of…
ODI #11715942 · Filed February 5, 2026
I looked up recalls on my vehicle and it states that The 2011 Mazda6 is part of a recall (NHTSA 19V-323, Mazda 2818I) covering 2011-2013 models for front cross member (subframe) corrosion due to insufficient rust protection . In salt-belt states, this corrosion can cause the lower control arm to…
ODI #11649768 · Filed March 21, 2025
The contact owns a 2010 Mazda Mazda6. The contact stated that while driving at an undisclosed speed, the vehicle inadvertently veered to the left. There was no warning light illuminated. The contact stated that the vehicle became difficult to steer. The vehicle was taken to an independent mechanic…

Read all 225 complaints

Owner-reported

2010 Mazda MAZDA6 mileage at failure

137 of the 225 complaints on file for the 2010 Mazda MAZDA6 give the vehicle's mileage when the problem happened.

Mileage at failure by component, from owners' complaints to NHTSA
Component	Median	Middle half	Based on
Structure	Median 90,000 miles	Middle half 50,000–130,000 miles	Based on 46 complaints

A component's median is its 50th percentile, and its middle half runs from its 25th to its 75th percentile.

Owners give the mileage themselves, often as a round number, and NHTSA doesn't check it. A complaint that names several components counts under each one, and mileages that can't be right, such as 999,999, or 50 miles on a five-year-old car, are left out.

These figures describe the complaints owners filed. They don't predict when a particular vehicle will have a problem, and vehicles that never had one aren't counted.

Mileage from NHTSA's complaints file of October 31, 2026. How these figures are worked out

NHTSA defect investigations

NHTSA's investigations file lists the 2010 Mazda MAZDA6 in 1 investigation. A listed model year means only that an investigation names it; it says nothing about any particular vehicle. An open investigation is not a finding that a safety defect exists, and NHTSA can close one without a recall.

Preliminary Evaluation PE18-006: Front Subframe Corrosion
Closed November 2, 2018
- Recall 18V-631

Open and recently closed NHTSA defect investigations

Passenger Frontal Air Bag Inflator May Explode

NHTSA #19V782000 · Air Bags — Frontal — Passenger Side — Inflator Module · NHTSA notice

Reported October 31, 2019 · Mazda North American Operations

Potentially affected: 69,879 vehicles

Repair completion: 67.9% (latest rate the manufacturer reported to NHTSA; dataset updated November 3, 2026)

Mazda campaign 1317F · Owners notified December 3, 2019 · Vehicles built April 11, 2008 – April 16, 2012 (per NHTSA) · Recall influenced by NHTSA's Office of Defects Investigation

Recall group: Takata airbag inflators

DO NOT DRIVE — this recall carries a "do not drive" advisory. Contact a Mazda dealer immediately.

Defect description

Mazda North American Operations (Mazda) is recalling certain 2007-2012 CX-7, CX-9, and 2009-2012 Maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Safety consequence

An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Manufacturer remedy

Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317F. Note: This recall supersedes recalls 16V356 and 17V012.

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Passenger Frontal Air Bag Inflator May Explode

NHTSA #18V717000 · Air Bags — Frontal — Passenger Side — Inflator Module · NHTSA notice

Reported October 12, 2018 · Mazda North American Operations

Potentially affected: 155,436 vehicles

Repair completion: 76.94% (latest rate the manufacturer reported to NHTSA; dataset updated November 3, 2026)

Mazda campaign 1317F · Owners notified November 9, 2018 · Vehicles built June 22, 2009 – August 24, 2012 (per NHTSA) · Recall influenced by NHTSA's Office of Defects Investigation

Recall group: Takata airbag inflators

DO NOT DRIVE — this recall carries a "do not drive" advisory. Contact a Mazda dealer immediately.

Defect description

Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2011-2013 Mazda6, 2011-2012 CX-7, and 2011-2015 CX-9 sold, or ever registered in the states of Arizona, Arkansas, Delaware, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, West Virginia and the District of Columbia, or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2010-2013 Mazda6, 2010-2012 CX-7, and 2010-2015 CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Safety consequence

An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Manufacturer remedy

Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began November 9, 2018. Owners may contact Mazda customer service at 1-800-222-5500, Option 4. Mazda's number for this recall is 1317F.

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Road Salt Causing Corrosion of Cross Member

NHTSA #18V631000 · Suspension — Front — Control Arm · NHTSA notice

Reported September 14, 2018 · Mazda North American Operations

Potentially affected: 50,176 vehicles

Repair completion: 46.53% (latest rate the manufacturer reported to NHTSA; dataset updated November 3, 2026)

Mazda campaign 2818I · Owners notified March 18, 2019 · Vehicles built February 4, 2008 – October 1, 2010 (per NHTSA) · Recall influenced by NHTSA's Office of Defects Investigation

Defect description

Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.

Safety consequence

Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.

Manufacturer remedy

Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Passenger Frontal Air Bag Inflator May Explode

NHTSA #18V018000 · Air Bags — Frontal — Passenger Side — Inflator Module · NHTSA notice

Reported January 9, 2018 · Mazda North American Operations

Potentially affected: 70,227 vehicles

Repair completion: 72.19% (latest rate the manufacturer reported to NHTSA; dataset updated November 3, 2026)

Mazda campaign 1317F · Owners notified March 2, 2018 · Vehicles built April 8, 2008 – August 24, 2012 (per NHTSA) · Recall influenced by NHTSA's Office of Defects Investigation

Recall group: Takata airbag inflators

DO NOT DRIVE — this recall carries a "do not drive" advisory. Contact a Mazda dealer immediately.

Defect description

Mazda North American Operations (Mazda) is recalling certain 2013 Mazda6 and CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2010 Mazda6, CX-7 and CX-9 vehicles sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2009 Mazda6, CX-7, and CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Safety consequence

An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Manufacturer remedy

Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began March 2, 2018. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F.

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Passenger Frontal Air Bag Inflator May Rupture

NHTSA #17V429000 · Air Bags — Frontal — Passenger Side — Inflator Module · NHTSA notice

Reported June 29, 2017 · Mazda North American Operations

Potentially affected: 205,377 vehicles

Repair completion: 44.38% (latest rate the manufacturer reported to NHTSA; dataset updated November 3, 2026)

Mazda campaign 1317F · Owners notified August 30, 2017 · Vehicles built February 4, 2008 – June 18, 2011 (per NHTSA) · Recall influenced by NHTSA's Office of Defects Investigation

Recall group: Takata airbag inflators

DO NOT DRIVE — this recall carries a "do not drive" advisory. Contact a Mazda dealer immediately.

Defect description

Mazda North America Operations (Mazda) is recalling certain 2009-2011 Mazda6, and 2007-2011 CX-7 and CX-9 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Safety consequence

An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Manufacturer remedy

Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the passenger frontal air bag inflator with an alternate inflator, free of charge. The recall began on August 30, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 16V356 and all vehicles that were not remedied under that campaign are now covered by this one.

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Air Bag Control Unit may Fail due to Moisture

NHTSA #16V594000 · Air Bags — Frontal — Sensor/Control Module-Inactive · NHTSA notice

Reported August 11, 2016 · Mazda North American Operations

Potentially affected: 41,918 vehicles

Repair completion: 53.93% (latest rate the manufacturer reported to NHTSA; dataset updated November 3, 2026)

Mazda campaign 9816H · Owners notified April 12, 2017 · Vehicles built February 4, 2008 – December 3, 2009 (per NHTSA) · Recall influenced by NHTSA's Office of Defects Investigation

Defect description

Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.

Safety consequence

Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.

Manufacturer remedy

Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Spiders may Block Fuel Tank Vent Line

NHTSA #14V114000 · Fuel System, Gasoline · NHTSA notice

Reported March 11, 2014 · Mazda North American Operations

Potentially affected: 42,000 vehicles

Repair completion: 51.43% (latest rate the manufacturer reported to NHTSA; dataset updated November 3, 2026)

Mazda campaign 7214C · Owners notified April 30, 2014 · Vehicles built September 14, 2009 – May 2, 2011 (per NHTSA)

Defect description

Mazda North America Operations (Mazda) is recalling certain model year 2010-2012 Mazda6 vehicles manufactured September 14, 2009, through May 2, 2011, and equipped with 2.5L engine. In the affected vehicles, spiders may weave a web in the evaporative canister vent hose, blocking it and causing the fuel tank to have an excessive amount of negative pressure.

Safety consequence

Negative pressure could cause the fuel tank to crack resulting in a fuel leak, increasing the risk of a fire.

Manufacturer remedy

Mazda will notify owners, and dealers will reprogram the powertrain control module and inspect and clean the canister vent line. If a web was found in the line, the fuel tank and check valve on canister vent line will be replaced. These repairs will be done free of charge. The recall began on April 30, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number associated with this campaign is 7214C.

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Door Latch Mounting Screws may Loosen

NHTSA #13V425000 · Latches/Locks/Linkages — Doors — Latch · NHTSA notice

Reported September 24, 2013 · Mazda North American Operations

Potentially affected: 161,400 vehicles

Repair completion: 58.25% (latest rate the manufacturer reported to NHTSA; dataset updated November 3, 2026)

Mazda campaign 7013I · Owners notified October 29, 2013 · Vehicles built February 4, 2008 – August 24, 2012 (per NHTSA) · Recall influenced by NHTSA's Office of Defects Investigation

Defect description

Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.

Safety consequence

If all three door latch mounting screws become excessively loose the door latch mechanism would not engage and the door might open while the vehicle is in motion increasing the risk of accident or injury.

Manufacturer remedy

Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on October 29, 2013. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number is 7013I.

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

FUEL TANK PRESSURE

NHTSA #11V134000 · Fuel System, Gasoline — Storage — Tank Assembly · NHTSA notice

Reported February 25, 2011 · MAZDA MOTOR CORP

Potentially affected: 52,000 vehicles

Mazda campaign 6211B · Owners notified March 25, 2011 · Vehicles built April 8, 2008 – February 8, 2010 (per NHTSA)

Defect description

MAZDA IS RECALLING CERTAIN MODEL YEAR 2009-2010 MAZDA6 VEHICLES MANUFACTURED FROM APRIL 8, 2008, THROUGH FEBRUARY 8, 2010. A CERTAIN TYPE OF SPIDER MAY WEAVE A WEB IN THE EVAPORATIVE CANISTER VENT LINE AND THIS MAY CAUSE A RESTRICTION IN THE LINE. IF THIS OCCURS, THE FUEL TANK PRESSURE MAY BECOME EXCESSIVELY NEGATIVE WHEN THE EMISSION CONTROL SYSTEM WORKS TO PURGE THE VAPORS FROM THE CANISTER.

Safety consequence

AS THE CANISTER IS PURGED REPEATEDLY DURING NORMAL OPERATION, THE STRESS ON THE FUEL TANK MAY EVENTUALLY RESULT IN A CRACK, POTENTIALLY LEADING TO FUEL LEAKAGE AD AN INCREASED RISK OF FIRE.

Manufacturer remedy

DEALERS WILL INSPECT AND CLEAN UP THE CANISTER VENT LINE, AND INSTALL A SPRING TO PREVENT THIS TYPE OF SPIDER FROM ENTERING THE VENT LINE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE MARCH 25, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.

Notes

MAZDA SAFETY RECALL NO. 6211B. OWNERS MAY ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S VEHICLE SAFETY HOTLINE AT 1-888-327-4236 (TTY 1-800-424-9153), OR GO TO <A HREF=HTTP://WWW.SAFERCAR.GOV>HTTP://WWW.SAFERCAR.GOV</A> .

2010 Mazda6 4-DR. w/SAB

—

out of 5

Overall Safety Rating

Not Rated

Frontal Crash

Not Rated

Driver: 5, Passenger: 5

Side Crash

Not Rated

Driver: 5, Passenger: 5

Side Pole

Not Rated

Rollover

Not Rated

Safety Technology

Electronic Stability Control

1 investigation

225 owner complaints have been filed with NHTSA for the 2010 Mazda MAZDA6.

Suspension

ODI #11746080

Incident: June 23, 2026 · Filed: June 23, 2026

I recently had my front subframe replaced as part of your recall, however, the rear subframe and all components attached are suffering from the exact same rust and potential component failure as the front. I was replacing my brakes today and noticed that the entire structure is on the verge of complete failure. The right rear suspension already makes unusual noises when going over even small bumps and I imagine if I were to hit a large pothole that would probably be the end of this car. I imagine all similar Mazda 6s in the Midwest suffer from the exact same degradation and it is a major safety concern. There are places where there's chunks of subframe missing because it has rusted completely through and just disintegrated.

Suspension; Unknown or Other

ODI #11715942

Incident: February 5, 2026 · Filed: February 5, 2026

I looked up recalls on my vehicle and it states that The 2011 Mazda6 is part of a recall (NHTSA 19V-323, Mazda 2818I) covering 2011-2013 models for front cross member (subframe) corrosion due to insufficient rust protection . In salt-belt states, this corrosion can cause the lower control arm to detach, reducing steering control and increasing crash risk. Key Details regarding the 2011 Mazda6 Subframe Recall: Scope: The recall affects specific 2011-2013 Mazda6 vehicles (and 2009-2010 models in a previous, related recall). Location Restrictions: Vehicles must have been originally sold in, or currently/previously registered in, 23 "salt belt" states (including CT, NY, MI, MN, OH, etc.). The Issue: The front cross member may experience severe corrosion, causing structural failure of the passenger-side lower control arm mounting point. Symptoms: Drivers may notice a change in steering alignment or a broken cross member. Remedy: Dealers will inspect the cross member and replace it if necessary. Action Required: Owners should contact their local Mazda dealership to check their VIN for open recalls. The recall was officially announced in May 2019 and is an expansion of a 2018 action.

Steering; Structure

ODI #11649768

Incident: March 21, 2025 · Filed: March 21, 2025

The contact owns a 2010 Mazda Mazda6. The contact stated that while driving at an undisclosed speed, the vehicle inadvertently veered to the left. There was no warning light illuminated. The contact stated that the vehicle became difficult to steer. The vehicle was taken to an independent mechanic where it was diagnosed and determined that the engine cradle had failed and was severely rusted and needed to be replaced. The vehicle was not repaired. The dealer was contacted; however, the vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 114,000.

Air Bags

ODI #11643653

Incident: February 19, 2025 · Filed: February 19, 2025

The airbag light is still flashing on the dashboard after the airbag recall on this vehicle was fixed. It may be related to a different recall, which is safety campaign #16V594000.

Suspension

ODI #11624391

Incident: November 9, 2024 · Filed: November 9, 2024

Extensive rust and corrosion in rear subframe. So severe the vehicle is unsafe to drive.

Suspension

ODI #11604971

Incident: July 26, 2024 · Filed: July 28, 2024

2010 mazda 6 i series sedan the entire rear subframe/cradle is rotted along with all the other parts connected to it, the A arm, bumper stops, control arms, rear sway bar the entire rear under carriage. took it to the shop and they said there have been several complaints about this exact issue on several of these cars from 09-13 models. the parts was not painted correctly like the front that was recalled. exposed to all weather elements, the shop wants almost 4k for labor only to fix but the main problem is finding the rear subframe on these cars is almost impossible next to cost a fortune. now i have a yard ornament. junk yard wants to give me 170 bucks for the car but im not doing that. Mazda needs to fix this issue. i would of never know it was rotted out unless i took it to the shop for rear swaying and sagging. its all over the road. very dangerous and will cause a wreck almost certainly. please someone do something about this issue. dont have the money to fix this let alone buy another car.

Suspension

ODI #11587423

Incident: March 1, 2024 · Filed: May 7, 2024

The rear subframe is compromised; it separated from the body of the car. The vehicle is in my driveway and available for inspection should the need arise. The rear end had felt a bit shaky for a month so I took it to my mechanic, who declared the vehicle "unfit for the road" due to the fact that the subframe was rotted away and detached from the car itself. I was told one big bump is an accident waiting to happen...pieces of the car would go flying and I could be left with zero mobility to evade oncoming traffic. The possibility of projectiles injuring anyone around the car was enough for me to park it. The car has not been inspected by Mazda, the police, or insurance because there was no accident. Since it's not safe to drive, I took the word of my independent mechanic rather than driving it to a dealership. There were no warnings other than a bit of a sway in the rear end, which I originally attributed to its age. I've researched the issue and it seems to be a result of subpar quality with regard to the metal that was used in manufacturing.

Structure

ODI #11572146

Incident: February 11, 2024 · Filed: February 15, 2024

The contact owns a 2010 Mazda Mazda6. The contact stated while driving 40–45 MPH, there was an abnormal sound coming from the vehicle. The TPMS warning light was illuminated. The vehicle was taken to an independent mechanic, who informed the contact that the rear main sub frame was completely rusted. There was a crack detected in the middle of the sub frame. The vehicle was taken to the local dealer, where it was diagnosed that the rear sub frame was rusted and needed to be replaced. The vehicle was not repaired. The manufacturer informed the contact that it was normal wear and tear, but no assistance was provided. The failure mileage was approximately 130,000.

Suspension

ODI #11570548

Incident: February 7, 2024 · Filed: February 7, 2024

Rear sub frame on car rusting out. Never protected from corrosion or rust. Car is currently in shop. Car has rusted out in the joint just behind drivers rear tire. Received notice of recall on the front of car due to salt and weather conditions front sub frame area replaced . Currently multiple cars have same issues Mazda hasnt fixed or issued any repairs for this

Suspension

ODI #11549093

Incident: October 9, 2023 · Filed: October 9, 2023

My gf went for a basic oil change and the automotive person was shocked to find the rear right cross bar to be suffering from incredible corrosion. He said at this point it is unsafe to drive. We looked into recalls for this make and model and there is one for the front cross bar due to insufficient or improper application of a corrosion spray on the frame. How can they say the front needs to be recalled and not the back? If the dealership didn’t do a good job of covering the appropriate metal frame in corrosion resistant spray any car that has that level should be recalled. This is immensely dangerous

Other Mazda MAZDA6 model years

Check your 2010 Mazda MAZDA6 VIN

Not every recall applies to every VIN in a given year. Enter the 17-character VIN from your Mazda MAZDA6 at nhtsa.gov/recalls to see whether your specific vehicle has an unrepaired recall.

Check a Mazda VIN